Part No. or keyword £º  
 
;
 

P150 Phaseshifter mounted to Motor Drive

 
GENERAL SPECIFICATIONS
( MOTOR DRIVE UNIT ONLY)

Electrical

Motor Drive Connector: 9-Pin D-Sub (male)

Voltage: 18-30VDC

Max. Amperage: 250mA & 600mA starting

Mechanical

Body: Aluminum Construction

Operating Temp:

Finish: Unique corrosion resistant 316 stainless steel epoxy coating IAW MIL-F-14072

  • ATM's motor driven phase shifters utilize DC motors with integrated, long life gear reductions ideal for High Reliability applications.

  • The unit will operate with a set DC voltage between 18-30VDC, commonly found in most systems or by a separate DC power supply. Motor speed will vary based on Voltage used. Maximum running current is 250mA & 600mA max starting.

  • To prevent motor damage, Micro switches are used to stop the motor at the minimum and maximum travel positions

  • Units are provided with a 9 pin D Sub Male connector allowing for control voltage, end point indication if desired, and follower potentiometer. See connector pin-out details.

  • These devices are best controlled by an external Double-Pole/Double-Throw (DPDT) switch or the optional ATM External control module.

  • Any one of ATM's Phase Shifters can be mounted to a motor drive.

 

Interface

1. Motor Control Voltage
Pins 2 and 7 of the nine pin D Sub male connector will have fixed DC voltage between 18-30 volts applied.  To increase phase pin 2 is (+) and pin 7 is (-).  To reverse the direction 2 is (-) and 7 is (+).  In both directions a stop is provided by means of Micro switches.


2. End Point Indicator *
The switch is also used to provide end point indication by means of pins 1 and 6 developing a voltage when the device has reached the maximum limit, (for 2+ and 7-). Pins will 3 and 8 will develop a voltage when a minimum limit is met. (for 2- and 7+). The developing voltage is equal to supply voltage used.


3. Follower Potentiometer **
A 10K Pot with an output proportional to the position of the motor drive mechanism is available at pins 4, 5, and 9.

MOTOR SPEED / RESPONSE TIME

ATM MODEL # DEG/GHz CASE LENGTH TIME*
P140/P240 30¡ã 3.75" 30 sec.
P150/P250 60¡ã 5.50" 14 sec.
P160/P260 90¡ã 7.0" 20 sec.
P1210/P2210 180¡ã 12.0" 40 sec.
P1100/P2100 360¡ã 24.0" 30 sec.

* approximate time to drive the phaseshifter from min to max. for given model, ( using sufficient voltage).

 
CONNECTOR PIN OUT

Pin # Function
+ 2 Increase Phase
- 7
- 2 Decrease Phase
+ 7
+ 1 * End Point Indicator
(Max. Phase)
   6
- 3 * End Point Indicator
(Min. Phase)
   8
** 10K Follower Potentiometer
4 Pot End Points
9
5 Wiper

 

Standard Models

Basic Phaseshifter

Type

 Generic* Model

No. (SMA)

 Outline Dwg.
30¡ã/GHz P14XX-28 30¡ã
60¡ã/GHz P15XX-28 60¡ã
90¡ã/GHz P16XX-28 90¡ã
180¡ã/GHz P121X-28 180¡ã
360¡ã/GHz P11XX-28 360¡ã
* When ordering a Motor Driven Phase Shifter, you will need to create the actual model number, based on the specific phaseshifter of you choosing by adding the suffix -28 at the end of the model number.

See our Phase Shifter page to find the  30¡ã,  60¡ã,  90¡ã, 180¡ã or 360¡ã model you wish to start with.

 

Example:   P/N P1604 becomes P1604-28 when ordering as a motor driven unit.

 

Any one of ATM's Phase Shifters can be mounted to a motor drive.

 

Optional External Control Module

An External Drive Control Module, part number MCM-001 shown at right, is available for the motor drive as an optional accessory. It includes:
 
1.  Crisp tactile switches to control drive.
2.  Max/Min position indicator lights.
3.  Follower potentiometer terminals.
4.  Self-switching power supply with input of 120 VAC - 240VAC.*     
5.  6 Ft, 9 pin cable to interconnect the control box to the motor driven device.  

*If supplied power source is not used, an input of 18-30 VDC through the 9 pin connector may be substituted.

 
 
111111111111